Tatted Goodie Bowl

2012_09_bowl3w
2012_09_bowl2w



Here is another project where I set out to make something and ended up with something else. I had originally meant to make this little bowl to fit a little, plastic shot glass I found at the party store. When I finished it, I saw that it would be really hard to stretch it over the glass until the stiffener dried. So I set it down while I thought about it.

I looked at it again, and saw that it was cute just sitting there, so I decided against the shot glass and instead threaded some wide ribbon through it. It’s a great size for some candies.

This is a beginner pattern and requires only one shuttle.

I used Lizbeth size 20 thread color white.

Printable pattern (92K. Opens a new window.)

Get Adobe ReaderPatterns are available for download as a PDF file and are readable by using Adobe Reader. Download Adobe Reader free.

You will need:

Thread in your choice of color and size.
1 tatting shuttle
5/8″ or 1/2″ wide (19 or 13 mm) ribbon
Hot glue

dsdouble stitch
ppicot
lplong picot
jjoin

This article may be helpful in making this pattern.
How to avoid a twisted picot

Instructions:

Row 1

R: (2ds p) 5 times, 2ds, close, turn
*Ch: (2ds p) 5 times, 2ds, turn
R: 2ds p 2ds j to fourth p of previous R, (2ds p) 3 times, 2ds, close, turn*
Repeat between * until there are a total of five rings.
Ch: (2ds p) 5 times, 2ds, turn
R: 2ds p 2ds j to fourth p of previous R, 2ds p 2ds j to 2nd p of first R, 2ds p 2ds, close, turn
Ch: (2ds p) 5 times, 2ds
Cut and tie.

Row 2

R: (2ds p) 2 times, 2ds, j to 4th p of any Ch of previous row, (2ds p) 2 times, 2ds, close, turn
**Leave about 3/4″ (22 mm) of thread between this ring and the next ring
Clover: R: (2ds p) 5 times, 2ds, close, do not turn
R: 2ds j to last p of previous R, (2ds p) 3 times, 2ds lp (2ds p) 4 times, 2ds close, do not turn
R: 2ds j to last p of previous R, (2ds p) 4 times, 2ds, close, turn
Leave about 3/4″ (22 mm) of thread between this ring and the next ring
R: (2ds p) 2 times, 2ds, j to 2nd p of the same Ch of previous row, (2ds p) 2 times, 2ds, close, turn
Leave about 3/4″ (22 mm) of thread between this ring and the next ring
R: 2ds p 2ds j to center p of last R on clover, 2ds p 2ds lp (2ds p) 3 times, 2ds, close, turn
R: (2ds p) 2 times, 2ds, j to 4th p of next Ch of previous row, (2ds p) 2 times, 2ds, close, turn**
Repeat between ** around, joining to the first Clover with the last ring you make.
Cut and tie.

Weave the ribbon through the second row, overlap ends and glue into place. Make a bow and glue it in place.

Tatting: Tatted Goodie Bowl visual pattern
Copyright 2012 by Nancy Tracy, All Rights Reserved.

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google photo

You are commenting using your Google account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )

Connecting to %s